This is a working overview of Primary drying, written for readers who want more than a one-paragraph summary but less than a textbook.
This page was last updated on 2025-11-28 and is reviewed periodically as new material appears.
Freezing determines ice crystal structure and pore size, which affect drying speed and product uniformity. Rapid freezing creates small crystals, while slow freezing creates larger crystals and often faster sublimation. During primary drying, chamber pressure is held below the vapor pressure of ice, and shelf temperature supplies heat for sublimation. The ice front recedes, leaving a porous matrix. Thermal limits such as collapse and eutectic temperatures set safe boundaries for formulation. These limits vary with solute composition and concentration.
Secondary drying removes bound water that remains after ice sublimation. Shelf temperature is raised gradually while pressure remains low, reducing water content to a target range. Over-drying can cause brittleness or electrostatic issues, while under-drying affects stability. The endpoint is often judged by pressure rise tests, temperature measurements, or water content analysis. Scale-up depends on matching heat and mass transfer across equipment sizes. Small changes in shelf temperature or pressure can alter cycle length substantially.
Lyophilization, or freeze-drying, removes water from a material by freezing it and then lowering pressure so ice changes directly to vapor. The process relies on sublimation, the phase transition from solid to gas without an intervening liquid state. It is used for heat-sensitive materials that would degrade in conventional drying. The three stages are freezing, primary drying, and secondary drying, each with distinct temperature and pressure requirements. In practice, cycle design balances these variables.
Lyophilization removes water from a frozen material by sublimation under reduced pressure. The process begins with freezing, which converts liquid water into ice and concentrates dissolved solids. Primary drying then lowers chamber pressure so ice changes directly into vapor without passing through a liquid phase. Secondary drying raises the shelf temperature to remove bound water that remains after ice sublimation. The result is a dry, porous structure that can be reconstituted later.
Formulation composition influences whether freeze-drying produces an intact cake or a collapsed mass. Excipients such as sugars and polymers can raise the collapse temperature and provide bulk during drying. The critical temperature for primary drying is often the collapse temperature or the glass transition temperature of the maximally concentrated phase. If the product temperature exceeds this threshold, the frozen matrix may soften and lose structure. Established practice therefore links shelf temperature and chamber pressure to the formulation's thermal properties.
The physics of freeze-drying couples heat transfer, mass transfer, and phase change. Heat supplied through the shelf must reach the sublimation front without melting the ice or degrading the product. Water vapor then travels through the already dried layer and leaves the chamber, where low pressure and cold traps keep it from returning. The dried layer acts as a resistance to vapor flow, so drying rate changes as the front recedes. Open questions remain about how pore structure and formulation heterogeneity affect drying uniformity at larger scales.
| Property | Value | Notes |
|---|---|---|
| Process name | Lyophilization or freeze-drying | Both terms appear in technical standards and literature. |
| Phase transition | Sublimation | Solid ice becomes vapor without a liquid step. |
| Typical chamber pressure | 0.05-0.5 mbar | Range depends on product temperature and equipment. |
| Typical product temperature | -40 °C to -10 °C | Measured during primary drying; formulation sets limits. |
| Water content after drying | 0.5-3% w/w | Target varies by material and stability needs. |
Lyophilization is a dehydration process that removes water from a frozen material by sublimation under low pressure. The material is first frozen so that water becomes ice; then the surrounding pressure is lowered below the vapor pressure of ice. Heat is applied gently so ice changes directly to vapor without passing through a bulk liquid phase. The vapor is collected on a cold condenser, leaving a dry porous matrix. This process differs from simple evaporation because the material remains frozen during the main drying stage.
The process usually has three stages: freezing, primary drying, and secondary drying. Freezing sets the ice crystal structure and can determine pore size in the final cake. Primary drying removes free ice by sublimation at low pressure and low shelf temperature. Secondary drying removes bound water by raising the shelf temperature, although some water may remain as part of the solid. Cycle parameters depend on formulation, fill volume, vial type, and equipment performance.
The physical chemistry of freezing influences whether a formulation forms an amorphous glass or a crystalline solid. Amorphous systems can collapse if product temperature rises above the glass transition temperature of the freeze concentrate. Crystalline systems may show eutectic melting, where ice and solute melt together at a fixed temperature. Formulators add bulking agents, lyoprotectants, and buffers to preserve structure and biological activity. The optimum cycle keeps product temperature below critical thresholds during primary drying while allowing efficient sublimation.
Lyophilization is a dehydration process that removes water from a frozen material by sublimation under low pressure. The material is first frozen to convert liquid water into ice. Next, the pressure is reduced below the triple point of water so that ice changes directly into vapor without passing through a liquid phase. This step is called primary drying. The result is a porous solid or cake that retains the original shape of the frozen solution.
After primary drying, secondary drying removes water that remains bound to the material. This stage raises the shelf temperature while maintaining low pressure, which encourages desorption of unfrozen water. Residual moisture can be reduced to a low percentage, improving stability for many products. The process parameters, including freezing rate, shelf temperature, and chamber pressure, influence the final pore structure and reconstitution behavior. Control of these variables helps prevent collapse or meltback during drying.
Lyophilization removes water by freezing a material and then lowering pressure so ice changes directly to vapor. The process relies on sublimation, the phase transition from solid to gas without an intermediate liquid state. Because the material remains frozen during primary drying, the structure often stays porous. This porous matrix can rehydrate quickly when water is added back. The low pressure also allows vapor to leave the solid matrix without boiling.
A typical cycle begins with freezing, which fixes the material into a solid and determines ice crystal size. Primary drying then raises heat under vacuum so ice sublimes, often near or below the collapse temperature of the formulation. Secondary drying removes bound water that remains after ice is gone, usually by gently warming the product. Each stage balances heat input against pressure to avoid melting or structural damage. Temperature probes and pressure sensors guide the transition between stages.
== Causes == Prolactin secretion is regulated by both stimulatory and inhibitory mechanisms. Dopamine acts on pituitary lactotroph D2 receptors to inhibit prolactin secretion while other peptides and hormones, such as thyrotropin releasing hormone (TRH), stimulate prolactin secretion. As a result, hyperprolactinemia may be caused by disinhibition (e.g., compression of the pituitary stalk or reduced dopamine levels) or excess production. The most common cause of hyperprolactinemia is prolactinoma (a type of pituitary adenoma). A blood serum prolactin level of 1000–5000 mIU/L (47–235 ng/mL) may arise from either mechanism, however levels >5000 mIU/L (>235 ng/mL) is likely due to the activity of an adenoma. Prolactin blood levels are typically correlated with the size of the tumors. Pituitary tumors smaller than 10 mm in diameter, or microadenomas, tend to have prolactin levels <200 ng/mL. Macroadenomas larger than 10 mm in diameter possess prolactin >1000 ng/mL. Hyperprolactinemia inhibits the secretion of gonadotropin-releasing hormone (GnRH) from the hypothalamus, which in turn inhibits the release of follicle-stimulating hormone (FSH) and luteinizing hormone (LH) from the pituitary gland and results in diminished gonadal sex hormone production (termed hypogonadism). This is the cause of many of the symptoms described below. In many people, elevated prolactin levels remain unexplained and may represent a form of hypothalamic–pituitary–adrenal axis dysregulation.
The (Princely) County of Tyrol was an estate of the Holy Roman Empire established about 1140. After 1253, it was ruled by the House of Gorizia and from 1363 by the House of Habsburg. In 1804, the County of Tyrol, unified with the secularised prince-bishoprics of Trent and Brixen, became a crown land of the Austrian Empire, then was part of Bavaria from 1805 to 1814 when it returned to Austrian rule. From 1867, it was a Cisleithanian crown land of Austria-Hungary. Today the territory of the historic crown land is divided between the Italian autonomous region of Trentino-Alto Adige/Südtirol and the Austrian state of Tyrol. The two parts are today associated again in the Tyrol–South Tyrol–Trentino Euroregion.
=== Herbivores === Herbivores consume ionone-containing carotenoids and convert those to retinal. Some species, including cattle and horses, have measurable amounts of β-carotene circulating in the blood, and stored in body fat, creating yellow fat cells. Most species have white fat and no β-carotene in circulation.
Sources: en.wikipedia.org
Muscle fatigue may be due to problems with the nerve supply, neuromuscular disease (such as myasthenia gravis), inborn errors of metabolism (such as metabolic myopathies), or problems with muscle itself. The latter category includes polymyositis and other muscle disorders.
Malaysia's main newspapers are owned by the government and political parties in the ruling coalition, although some major opposition parties also have their own, which are openly sold alongside regular newspapers. A divide exists between the media in the two halves of the country. Peninsular-based media gives a low priority to news from the East and often treats the eastern states as colonies of the peninsula. As a result of this, Sarawak launched TV Sarawak as an internet streaming beginning in 2014, and later as a TV station on 10 October 2020 to overcome the low priority and coverage of Peninsular-based media and to solidify the representation of East Malaysia. The media have been blamed for increasing tension between Indonesia and Malaysia, and giving Malaysians a bad image of Indonesians. The country has Malay, English, Chinese, and Tamil daily newspapers. Kadazandusun and Bajau news are available only via TV broadcast Berita RTM. Written Kadazan news was once included in publications such as The Borneo Post, the Borneo Mail, the Daily Express, and the New Sabah Times, but publication has ceased with the newspaper or as a section. Freedom of the press is limited, with numerous restrictions on publishing rights and information dissemination. The government has previously tried to crack down on opposition papers before elections. In 2007, a government agency issued a directive to all private television and radio stations to refrain from broadcasting speeches made by opposition leaders, a move condemned by politicians from the opposition Democratic Action Party.
Quercetin is the aglycone form of a number of other flavonoid glycosides, such as rutin (also known as quercetin-3-O-rutinoside) and quercitrin, found in citrus fruit, buckwheat, and onions. Quercetin forms the glycosides quercitrin and rutin together with rhamnose and rutinose, respectively. Likewise guaijaverin is the 3-O-arabinoside, hyperoside is the 3-O-galactoside, isoquercitin is the 3-O-glucoside and spiraeoside is the 4′-O-glucoside. CTN-986 is a quercetin derivative found in cottonseeds and cottonseed oil. Miquelianin is the quercetin 3-O-β-D-glucuronopyranoside. Several taxifolin (also known as dihydroquercetin) glycosides also exist. Isoquercetin is the 3-O-glucoside of quercetin.
Sources: en.wikipedia.org
Conventional drying uses heat to evaporate liquid water, often at temperatures that can degrade sensitive materials. Lyophilization freezes the material first and then removes water by sublimation under vacuum. This avoids prolonged exposure to liquid water and high heat.
Lowering pressure reduces the boiling point of water and allows ice to sublimate at temperatures below freezing. Vacuum also limits convective heat transfer, so heat is usually supplied by shelves or radiation. The pressure must stay below the vapor pressure of ice at the product temperature.
The cycle typically includes freezing, primary drying, and secondary drying. Freezing solidifies water and sets the pore structure; primary drying removes bulk ice; secondary drying removes bound water. Some cycles add annealing or pre-freezing steps.
Primary drying removes ice by sublimation at low pressure and low shelf temperature. Secondary drying removes bound water by raising the shelf temperature, often under the same vacuum. The two stages differ in the water state being removed.