If you have been reading about storage and want a single page that covers the useful parts, this is it: definitions, context, how it is studied, and the questions that come up repeatedly.
Last reviewed on 2026-01-06. Where a claim depends on a specific study, the study is described rather than over-claimed.
A typical cycle begins with freezing, sometimes including an annealing step to control ice crystal size. Freezing conditions influence the pore network that later allows vapor escape. During primary drying, shelf temperature and chamber pressure are set so heat enters the product while its temperature stays below the collapse or eutectic point. Secondary drying then raises the shelf temperature to desorb bound water and lower residual moisture. Cycle design depends on formulation, fill volume, container type, and equipment capability.
The physics of lyophilization couples heat transfer, mass transfer, and phase behavior. Sublimation requires a vapor pressure difference between the ice front and the chamber, and the dried layer adds resistance to vapor flow. Amorphous formulations are characterized by a glass transition temperature of the maximally freeze-concentrated solute, often denoted Tg'. Crystalline bulking agents can provide structure, while amorphous excipients stabilize labile components. Open questions remain about spatial heterogeneity, edge effects, and how laboratory cycles scale to production.
Lyophilization is a drying process in which a solvent, usually water, is removed from a frozen material by sublimation under reduced pressure. The material is first solidified, then placed under vacuum so that ice transitions directly to vapor without a bulk liquid phase. This approach suits heat-sensitive substances that would degrade during conventional evaporation. Primary drying removes unbound ice, while secondary drying reduces water that remains adsorbed to the solid matrix. The result is a porous, lightweight solid that can be reconstituted later.
Handling practices aim to prevent moisture ingress and mechanical damage. Vials should remain stoppered and crimped until use, and reconstitution should follow the labeled diluent and volume. Shipping may involve temperature-controlled containers and desiccants, but direct contact between desiccant and product is avoided. Regulatory guidance expects documented storage conditions, excursion assessments, and stability commitments. Open questions remain about how best to predict long-term stability from short accelerated studies for every formulation class.
After lyophilization, the product is usually a porous cake or powder with a large internal surface area. This structure can absorb moisture quickly if exposed to humid air, so vials are sealed under vacuum or an inert gas. Moisture uptake may lower the glass transition temperature of the dried matrix and accelerate chemical or physical degradation. Storage conditions therefore depend on the formulation, container, and intended shelf life. Some products remain stable at room temperature, while others require refrigeration or freezing.
Quality control for lyophilized products includes appearance, cake structure, reconstitution time, pH, residual moisture, and potency. Residual moisture is a key attribute because excess water can reduce stability, while excessively low moisture may cause structural changes or aggregation in some systems. Stability studies compare real-time and accelerated conditions to estimate shelf life. Analytical methods must be validated for the specific matrix, container, and moisture range. Sterility and container integrity are also monitored for sterile products.
| Property | Value | Notes |
|---|---|---|
| Physical state | Solid, porous cake or powder | Depends on formulation and container |
| Typical storage temperature | 2–25 °C, protected from moisture | Some materials require colder conditions |
| Solubility class | Usually readily soluble after reconstitution | Not an intrinsic chemical property |
| Common analytical method | Karl Fischer titration | Used for residual moisture |
| Common synonyms | Freeze-drying; lyophilisation | Lyophilisation is a spelling variant |
The low pressure used during drying allows water vapor to move from the ice surface to a cold condenser. Energy supplied as heat drives sublimation but must stay below the collapse temperature of the frozen matrix. If the product becomes too warm, the frozen structure may soften or melt, reducing pore formation and slowing drying. Formulations often include bulking agents, stabilizers, or buffers to support a rigid cake. The final moisture content depends on formulation, freezing rate, and the length of secondary drying.
Freeze-drying is distinct from simple evaporation and from spray drying. Evaporation removes water at temperatures above freezing, while spray drying rapidly dries droplets in a heated gas stream. Lyophilization avoids high temperatures, which can be useful for heat-sensitive materials such as proteins, vaccines, and some foods. The porous cake produced by sublimation dissolves or rehydrates more quickly than a dense dried mass. Not all materials tolerate freezing or the pH shifts that can occur as solutes concentrate during ice formation.
Lyophilized products are typically hygroscopic and require protection from moisture during storage. Manufacturers seal them in glass vials, often under vacuum or an inert gas such as nitrogen. The container closure system, including the stopper and crimp seal, must prevent water vapor ingress. Storage temperature varies from controlled room temperature to refrigerated or frozen conditions, depending on the formulation. Humidity-controlled environments are essential because even brief exposure to ambient air can degrade the product.
Stability of a lyophilized product depends on its glass transition temperature, the temperature at which the amorphous cake transitions from a glassy to a rubbery state. Storage below this temperature minimizes molecular mobility and slows chemical degradation. If the storage temperature exceeds the glass transition temperature, the cake may collapse, shrink, or become sticky. Accelerated stability studies at elevated temperatures and humidity help predict shelf life, but they do not always reflect real-time behavior. Residual moisture content also plays a critical role in long-term stability.
Formulation composition influences whether freeze-drying produces an intact cake or a collapsed mass. Excipients such as sugars and polymers can raise the collapse temperature and provide bulk during drying. The critical temperature for primary drying is often the collapse temperature or the glass transition temperature of the maximally concentrated phase. If the product temperature exceeds this threshold, the frozen matrix may soften and lose structure. Established practice therefore links shelf temperature and chamber pressure to the formulation's thermal properties.
The physics of freeze-drying couples heat transfer, mass transfer, and phase change. Heat supplied through the shelf must reach the sublimation front without melting the ice or degrading the product. Water vapor then travels through the already dried layer and leaves the chamber, where low pressure and cold traps keep it from returning. The dried layer acts as a resistance to vapor flow, so drying rate changes as the front recedes. Open questions remain about how pore structure and formulation heterogeneity affect drying uniformity at larger scales.
Lyophilization removes water from a frozen material by sublimation under reduced pressure. The process begins with freezing, which converts liquid water into ice and concentrates dissolved solids. Primary drying then lowers chamber pressure so ice changes directly into vapor without passing through a liquid phase. Secondary drying raises the shelf temperature to remove bound water that remains after ice sublimation. The result is a dry, porous structure that can be reconstituted later.
=== MC1R and infection/inflammation === The involvement of MC1R in a rat model of Candida albicans vaginitis was investigated. These authors suggest that MC1R is important in anti-fungal and anti-inflammatory processes, in part because siRNA knockdown of MC1R almost completely prevented the responses. Nosocomial infections are of variable importance. One of the most important is complicated sepsis, which was defined as sepsis with organ dysfunction. One variant of MC1R (MC1RR163Q, rs885479) was reported to be associated with lowered risk of developing complicated sepsis during hospitalization after trauma. Thus, if the association is confirmed, MC1R targeting may become a therapeutic option to prevent severe sepsis.
Angelicin synthase is a cytochrome P450 protein containing heme, isolated from parsnip. It uses molecular oxygen for the oxidation and requires a partner cytochrome P450 reductase for functional expression. This uses nicotinamide adenine dinucleotide phosphate.
=== Resins === Urea is a raw material for the manufacture of formaldehyde based resins, such as UF, MUF, and MUPF, used mainly in wood-based panels, for instance, particleboard, fiberboard, OSB, and plywood.
MD-derived structure predictions can be tested through community-wide experiments in Critical Assessment of Protein Structure Prediction (CASP), although the method has historically had limited success in this area. Michael Levitt, who shared the Nobel Prize partly for the application of MD to proteins, wrote in 1999 that CASP participants usually did not use the method due to "... a central embarrassment of molecular mechanics, namely that energy minimization or molecular dynamics generally leads to a model that is less like the experimental structure". Improvements in computational resources permitting more and longer MD trajectories, combined with modern improvements in the quality of force field parameters, have yielded some improvements in both structure prediction and homology model refinement, without reaching the point of practical utility in these areas; many identify force field parameters as a key area for further development. MD simulation has been reported for pharmacophore development and drug design. For example, Pinto et al. implemented MD simulations of Bcl-xL complexes to calculate average positions of critical amino acids involved in ligand binding. Carlson et al. implemented molecular dynamics simulations to identify compounds that complement a receptor while causing minimal disruption to the conformation and flexibility of the active site. Snapshots of the protein at constant time intervals during the simulation were overlaid to identify conserved binding regions (conserved in at least three out of eleven frames) for pharmacophore development.
Produce a book and a film about Omar ibn Said Provide public access to "programs that enhance knowledge about faiths practiced in the regions, including Indigenous African religious traditions, Judaism, Christianity, Islam, and their influence on daily life." On May 8, 2025, two days after Hayden had given testimony to the Senate Committee on Appropriations and the Committee on House Administration, via email and without any explanation, she was abruptly fired by President Trump. Publishers Weekly characterized Hayden's termination as the "latest blow to professional research and the literary and arts community." No replacement of Hayden has been nominated. Principal Deputy Librarian Robert Newlen, who would have served as interim librarian was fired and Trump named Deputy Attorney General Todd Blanche as acting librarian of Congress and later fired the deputy librarian and copyright office director (Perlmutter and Newlen), appointing senior DOJ officials Brian Nieves and Paul Perkins as respectively, for the interim. This has been interpreted as an attack on the separation of powers. Perlmutter has sued to dispute the legality of the dismissal, as the register is appointed by, and responsible to, the librarian of Congress.
Sources: en.wikipedia.org
The disease progresses by forming granulation tissue at the edges of the synovial lining, pannus with extensive angiogenesis and enzymes causing tissue damage. The fibroblast-like synoviocytes have a prominent role in these pathogenic processes. The synovium thickens, cartilage and underlying bone disintegrate, and the joint deteriorates, with raised calprotectin levels serving as a biomarker of these events. Cytokines and chemokines attract and accumulate immune cells, i.e., activated T- and B cells, monocytes, and macrophages from activated fibroblast-like synoviocytes, in the joint space. By signalling through RANKL and RANK, they eventually trigger osteoclast production, which degrades bone tissue. The fibroblast-like synoviocytes that are present in the synovium during rheumatoid arthritis display altered phenotype compared to the cells present in normal tissues. The aggressive phenotype of fibroblast-like synoviocytes in rheumatoid arthritis and the effect these cells have on the microenvironment of the joint can be summarized into hallmarks that distinguish them from healthy fibroblast-like synoviocytes. These hallmark features of fibroblast-like synoviocytes in rheumatoid arthritis are divided into seven cell-intrinsic hallmarks and four cell-extrinsic hallmarks. The cell-intrinsic hallmarks are: reduced apoptosis, impaired contact inhibition, increased migratory invasive potential, changed epigenetic landscape, temporal and spatial heterogeneity, genomic instability and mutations, and reprogrammed cellular metabolism.
In 2007, a pet food recall was initiated by Menu Foods and other pet food manufacturers who had found their products had been contaminated and caused serious illnesses or deaths in some of the animals that had eaten them. In March 2007, the US Food and Drug Administration reported finding white granular melamine in the pet food, in samples of white granular wheat gluten imported from a single source in China, Xuzhou Anying Biologic Technology as well as in crystalline form in the kidneys and in urine of affected animals. Further vegetable protein imported from China was later implicated. In April 2007, The New York Times reported that the addition of "melamine scrap" into fish and livestock feed to give the false appearance of a higher level of protein was an "open secret" in many parts of mainland China, reporting that this melamine scrap was being produced by at least one plant processing coal into melamine. Four days later, the New York Times reported that, despite the widely reported ban on melamine use in vegetable proteins in mainland China, at least some chemical manufacturers continued to report selling it for use in animal feed and in products for human consumption. Li Xiuping, a manager at Henan Xinxiang Huaxing Chemical in Henan Province, stated, "Our chemical products are mostly used for additives, not for animal feed.
Microorganisms have a minimum temperature, an optimum, and a maximum temperature for growth. High temperature as well as low temperatures are used as physical agents of control. Different organisms show different degrees of resistance or susceptibility to heat or temperature, some organisms such as bacterial endospore are more resistant while vegetative cells are less resistant and are easily killed at lower temperatures. Another method that involves the use of heat to kill microorganisms is fractional sterilization. This process involves the exposure to a temperature of 100 degrees Celsius for an hour per day for several days. Fractional sterilization is also called tyndallization. Bacterial endospores can be killed using this method. Both dry and moist heat are effective in eliminating microbial life. For example, jars used to store preserves such as jam can be sterilized by heating them in a conventional oven. Heat is also used in pasteurization, a method for slowing the spoilage of foods such as milk, cheese, juices, wines and vinegar. Such products are heated to a certain temperature for a set period of time, which greatly reduces the number of harmful microorganisms. Low temperature is also used to inhibit microbial activity by slowing down microbial metabolism.
In Greece, during a civil war involving the communist-led partisan movement ELAS-EAM, British Special Forces terminated arms supplies to the ELA-ELAM, pro-monarchist armed forces were strengthened. On the political front, Americans, with British encouragement, attempted to dismantle ELAS-EAM socialist structures in the countryside, and an anti-communist swing gradually occurred. Western Allies conducted meetings in Italy in March 1945 with German representatives to forestall a takeover by Italian communist resistance forces in northern Italy and to hinder the potential there for post-war influence of the civilian Italian Communist Party. The affair caused a major rift between Stalin and Churchill, and in a letter to Roosevelt on 3 April Stalin complained that the secret negotiations did not serve to "preserve and promote trust between our countries".
Sources: en.wikipedia.org
=== 19th century === Michael Faraday provided the first description, in scientific terms, of the optical properties of nanometer-scale metals in his classic 1857 paper. In a subsequent paper, the author (Turner) points out that: "It is well known that when thin leaves of gold or silver are mounted upon glass and heated to a temperature that is well below a red heat (~500 °C), a remarkable change of properties takes place, whereby the continuity of the metallic film is destroyed. The result is that white light is now freely transmitted, reflection is correspondingly diminished, while the electrical resistivity is enormously increased."
The positive side of freedom of association is that the law protects everyone against adverse action for joining a union, and also taking part in collective action including strikes that count as "protected industrial action". If an employee alleges that the employer has taken adverse action for a prohibited reason, "it is presumed that the action was, or is being, taken for that reason or with that intent, unless the [employer] proves otherwise." The claimant may apply to the Fair Work Commission which holds a conference, compulsory in cases of dismissal, and the FWC may arbitrate with the parties' consent. Despite the intent of Parliament, in Board of Bendigo Regional Institute of Technical and Further Education v Barclay the High Court held that the reverse burden of proof made it legitimate to focus on the subjective reasons of the decision-maker, so that direct "testimony from the decision-maker which is accepted as reliable is capable of discharging the burden", and that this achieved a "balance". The High Court repeated this stance in CFMEU v BHP Coal Pty Ltd, where a striking worker held a sign saying "No principles SCABS No Guts", and was dismissed for violating BHP's "workplace conduct policy". The High Court sided with the employer's assertion that dismissal was for uncivil language, not union activity, and said that a claimant would only be protected from an employer's deliberate and conscious victimisation, not employers who make out they (supposedly) inadvertently took adverse action.
== Assays for DBH activity in human serum and cerebrospinal fluid == DBH activity in human serum could be estimated by a spectrophotometric method or with the aid of ultra-high-performance liquid chromatography with photo diode array detector (UHPLC-PDA). A sensitive assay for the detection of DBH activity in cerebrospinal fluid using high-performance liquid chromatography with electrochemical detector (HPLC-ECD) was also described earlier.
Sources: en.wikipedia.org
Freezing only converts liquid to solid. Lyophilization adds vacuum and controlled warming so frozen solvent sublimes, leaving a dry porous solid. The two steps are related but not interchangeable.
Reduced pressure keeps the solvent below its triple point, allowing ice to become vapor without melting. Vacuum also helps remove water vapor from the product chamber. The exact pressure is chosen with the formulation and equipment.
Residual moisture is water that remains in the dried solid after secondary drying. It is often measured by Karl Fischer titration, near-infrared spectroscopy, or thermogravimetry. Acceptable levels depend on the material and its stability profile.
Collapse occurs when the product temperature rises above its collapse or eutectic temperature during drying. The frozen matrix loses structure, producing a shrunken or melted appearance. This can slow reconstitution and may affect stability.