Secondary drying is one of those subjects where the details matter more than the headlines. This page pulls together the background, the mechanisms, and the practical points readers ask about most.
Last reviewed on 2026-01-07. Where a claim depends on a specific study, the study is described rather than over-claimed.
Lyophilization is a dehydration technique in which a product is frozen and the solvent is removed under reduced pressure. The low pressure allows ice to sublimate directly into vapor without passing through a bulk liquid phase. This differs from conventional drying, where heat drives evaporation and can damage heat-sensitive structures. The process is used for biological materials, pharmaceutical formulations, and some foods. Its main advantage is preservation of porous structure and rapid reconstitution.
Freezing is the first stage and sets the ice structure that later becomes the pore network. The formulation is cooled below its freezing point, often with a controlled ramp, and solutes concentrate as ice forms. Primary drying then lowers chamber pressure and supplies heat to sublime the ice. The product temperature must stay below its collapse or eutectic temperature to prevent structural loss. Secondary drying raises the temperature modestly to remove bound water and achieve a low residual moisture.
A freeze-dryer consists of a vacuum chamber, temperature-controlled shelves, a condenser, and a vacuum pump. Vials, ampoules, or bulk trays hold the product during the cycle. The condenser traps water vapor as ice at a temperature lower than the product. Cycle development balances shelf temperature, chamber pressure, and time. Scale-up can be difficult because heat and mass transfer change with equipment size, so process analytical tools and conservative validation are often used.
Stability studies examine how temperature, humidity, and time influence a lyophilized product. Accelerated conditions provide early information about degradation pathways, while long-term studies support shelf-life claims. The glass transition temperature of the dried formulation can indicate its physical stability, and storage above this temperature may increase molecular mobility and lead to collapse or aggregation. Container closure integrity also matters because moisture or oxygen ingress can degrade the product, so vial stoppers and seals are part of the quality system.
Handling and storage practices aim to keep the cake intact and dry. Vials are typically stored upright at controlled temperatures, often between 2 °C and 8 °C or at -20 °C for longer-term use. Reconstitution involves adding a suitable diluent and gently mixing until the solid dissolves. Shaking or rapid injection of diluent can create foam or damage sensitive molecules. Once reconstituted, the product may require refrigeration and use within a defined period.
| Property | Value | Notes |
|---|---|---|
| Common synonyms | freeze-drying, lyophilisation, cryodesiccation | Lyophilization is common in pharmaceutical literature. |
| Typical chamber pressure during primary drying | 0.05–0.5 mbar (5–50 Pa) | Must remain below the triple point of water. |
| Typical shelf temperature during freezing | −40 to −20 °C | Lower temperatures may be used for eutectic systems. |
| Typical residual moisture after secondary drying | 0.5–3% w/w | Product-dependent; low moisture improves stability but can cause over-drying. |
| Typical analytical method for residual moisture | Karl Fischer titration or loss on drying | Thermogravimetric methods are also used. |
Secondary drying removes bound water that remains after ice sublimation. Shelf temperature is raised gradually while pressure remains low, reducing water content to a target range. Over-drying can cause brittleness or electrostatic issues, while under-drying affects stability. The endpoint is often judged by pressure rise tests, temperature measurements, or water content analysis. Scale-up depends on matching heat and mass transfer across equipment sizes. Small changes in shelf temperature or pressure can alter cycle length substantially.
Lyophilization, or freeze-drying, removes water from a material by freezing it and then lowering pressure so ice changes directly to vapor. The process relies on sublimation, the phase transition from solid to gas without an intervening liquid state. It is used for heat-sensitive materials that would degrade in conventional drying. The three stages are freezing, primary drying, and secondary drying, each with distinct temperature and pressure requirements. In practice, cycle design balances these variables.
Freezing determines ice crystal structure and pore size, which affect drying speed and product uniformity. Rapid freezing creates small crystals, while slow freezing creates larger crystals and often faster sublimation. During primary drying, chamber pressure is held below the vapor pressure of ice, and shelf temperature supplies heat for sublimation. The ice front recedes, leaving a porous matrix. Thermal limits such as collapse and eutectic temperatures set safe boundaries for formulation. These limits vary with solute composition and concentration.
Handling practices aim to prevent moisture ingress and mechanical damage. Vials should remain stoppered and crimped until use, and reconstitution should follow the labeled diluent and volume. Shipping may involve temperature-controlled containers and desiccants, but direct contact between desiccant and product is avoided. Regulatory guidance expects documented storage conditions, excursion assessments, and stability commitments. Open questions remain about how best to predict long-term stability from short accelerated studies for every formulation class.
After lyophilization, the product is usually a porous cake or powder with a large internal surface area. This structure can absorb moisture quickly if exposed to humid air, so vials are sealed under vacuum or an inert gas. Moisture uptake may lower the glass transition temperature of the dried matrix and accelerate chemical or physical degradation. Storage conditions therefore depend on the formulation, container, and intended shelf life. Some products remain stable at room temperature, while others require refrigeration or freezing.
In practice, lyophilization is slower and more energy intensive than simple drying. Cycle times can range from hours to several days depending on load, container, and formulation. Amorphous materials may require excipients that help preserve structure during freezing and drying. The method is widely used for biological materials, pharmaceuticals, and foods where heat drying would cause unacceptable change. Open questions remain about scaling cycles between laboratory and production equipment, and this gap affects technology transfer.
Lyophilization removes water by freezing a material and then lowering pressure so ice changes directly to vapor. The process relies on sublimation, the phase transition from solid to gas without an intermediate liquid state. Because the material remains frozen during primary drying, the structure often stays porous. This porous matrix can rehydrate quickly when water is added back. The low pressure also allows vapor to leave the solid matrix without boiling.
A typical cycle begins with freezing, which fixes the material into a solid and determines ice crystal size. Primary drying then raises heat under vacuum so ice sublimes, often near or below the collapse temperature of the formulation. Secondary drying removes bound water that remains after ice is gone, usually by gently warming the product. Each stage balances heat input against pressure to avoid melting or structural damage. Temperature probes and pressure sensors guide the transition between stages.
At this point, it was eagerly anticipated that such pharmacometabolomics approaches could be applied to personalized human medicine. Since this publication in 2006, the Pharmacometabolomics Research Network led by Duke University researchers and that included partnerships between centers of excellence in metabolomics, pharmacogenomics and informatics (over sixteen academic centers funded by NIGMS) has been able to illustrate for the first time the power of the pharmacometabolomics approach in informing about treatment outcomes in large clinical studies and with use of drugs that include antidepressants, statins, antihypertensives, antiplatelet therapies and antipsychotics. Totally new concepts emerged from these studies on use of pharmacometabolomics as a tool that can bring a paradigm shift in the field of pharmacology. It illustrated how pharmacometabolomics can enable a Quantitative and Systems Pharmacology approach. Pharmacometabolomics has been applied for the treatment of numerous human diseases, such as schizophrenia, diabetes, neural disease, depression and cancer.
The lightweight chain of a bicycle with derailleur gears can snap (or rather, come apart at the side-plates, since it is normal for the "riveting" to fail first) because the pins inside are not cylindrical, they are barrel-shaped. Contact between the pin and the bushing is not the regular line, but a point which allows the chain's pins to work its way through the bushing, and finally the roller, ultimately causing the chain to snap. This form of construction is necessary because the gear-changing action of this form of transmission requires the chain to both bend sideways and to twist, but this can occur with the flexibility of such a narrow chain and relatively large free lengths on a bicycle. Chain failure is much less of a problem on hub-geared systems since the chainline does not bend, so the parallel pins have a much bigger wearing surface in contact with the bush. The hub-gear system also allows complete enclosure, a great aid to lubrication and protection from grit.
=== Amber Holt === Amber Holt (Mae Whitman), age 16 at the beginning of the series, is Sarah's rebellious, willful, and not very studious daughter who is seeking direction in life. She resents her move from Fresno, particularly after her mother thwarts her efforts to stay by moving in with her boyfriend. She resents her father's drug use and abandonment more than her brother does because she claims that she can remember the hard times better than he can. At one point, she and her mother and brother were living in a motel together to be away from their father. She shows musical inclination and is a talented guitar player and songwriter. Toward the end of the second season, despite receiving a 2250 on her SATs and having a successful interview with a Berkeley alumna, Amber learns that she has been rejected from both colleges she applied to and has to decide what to do with her life. Following a path of drinking and drug abuse with her new friend, Gary (a coworker at Julia's law firm, where Amber briefly worked), the couple is violently T-boned by an SUV. Amber is critically injured but recovers and decides to start over. She then moves out of her grandparents' house and into her own apartment, but her relationships with her family, in particular her mother, remain intact. In season three, she works at a coffee shop before her aunt Kristina offers her an assistant position for Bob Little's political campaign. Amber is promoted to be Bob Little's assistant but then has a fling with him; Kristina discovers this and is disappointed with her (and loses trust in Little).
== Diagnosis == Lipedema requires diagnosis in a medical office by a clinician (a “clinical diagnosis”). A trained clinician reaches the diagnosis by considering patient history, including family history, and a physical exam. Clinicians should avoid reliance purely on differential diagnosis as this will lead to a failure to diagnose people with lipedema when they present with other co-morbidities like lymphedema, chronic venous insufficiency. There is not yet a standardized test, such as bloodwork or imaging, that can confirm the presence of lipedema, however, there are common clinical presentations that are specific to lipedema.
Sources: en.wikipedia.org
The babies from this initial experiment were born in 1954, and the milestone was first publicized in the Cedar Rapids Gazette under the headline "Fatherhood After Death Has Now Been Proved Possible." After receiving his doctorate, Sherman accepted a position at the Biological Research Institute with the American Foundation for Biological Research in Madison, Wisconsin, in 1954. In 1957 Sherman joined the faculty at the University of Arkansas. He served as a professor there until 1992, when he became a professor emeritus and continued work until 1994. At University of Arkansas for Medical Sciences, he founded what is considered to be the second human semen cryobank. During his career, he also traveled by request to assist with the establishment of other cryobanks across the country. He also helped to establish and advocate for the Office of Minority Affairs within the School of Medical Sciences at Arkansas. From 1974 to 1975, he spent a year on sabbatical teaching at National Chung-Hsing University in Taichung, Taiwan. Throughout his career, Sherman was also active in professional societies including his role as a charter member of the Society of Cryobiology in 1964, where he also served on the society's editorial board; as a founder of the American Association of Tissue Banks, where he drafted the first standards for the cryobanking of human embryos; and as an advisor to the Food and Drug Administration on AIDS and cryobanking from 1988 to 1992.
== NAD+ precursors == The members of the NAD+ precursor family include tryptophan (Trp), nicotinic acid (NA), nicotinamide (NAM), nicotinamide ribose (NR), nicotinamide mononucleotide (NMN), reduced nicotinamide ribose (NRH) and reduced nicotinamide mononucleotide (NMNH) of these, the majority are logically vitamin B substances or their congeners Based on the bioavailability of its precursors, there are three pathways for the synthesis of NAD+ in cells.
transcription factor (TF) Any protein that controls the rate of transcription of genetic information from DNA to RNA by binding to a specific DNA sequence and promoting or blocking the recruitment of RNA polymerase to nearby genes. Transcription factors can effectively turn "on" and "off" specific genes in order to make sure they are expressed at the right times and in the right places; for this reason, they are a fundamental and ubiquitous mechanism of gene regulation.
A light-emitting diode (LED) is an electronic component that uses a semiconductor to emit light when current flows through it. Electrons in the semiconductor recombine with electron holes, thereby releasing energy in the form of photons. The color of the light (corresponding to the energy of the photons) is determined by the energy required for electrons to cross the band gap of the semiconductor. White light is obtained by using multiple semiconductors or a layer of light-emitting phosphor on the semiconductor device. Appearing as practical electronic components in 1962, the earliest LEDs emitted low-intensity infrared (IR) light. Infrared LEDs are used in remote-control circuits, such as those used with a wide variety of consumer electronics. The first visible-light LEDs were of low intensity and limited to red. Early LEDs were often used as indicator lamps, replacing small incandescent bulbs, and in seven-segment displays. Later developments produced LEDs available in visible, ultraviolet (UV), and infrared wavelengths with high, low, or intermediate light output; for instance, white LEDs suitable for room and outdoor lighting. LEDs have also given rise to new types of displays and sensors, while their high switching rates have uses in advanced communications technology. LEDs have been used in diverse applications such as aviation lighting, fairy lights, strip lights, automotive headlamps, advertising, stage lighting, general lighting, traffic signals, camera flashes, lighted wallpaper, horticultural grow lights, and medical devices.
For services to Public Health in Scotland. Gerard Anthony Lemos, CMG. Non-Executive Chair, HM Prisons and Probation Service Agency Board. For Public and Voluntary Service. Zoe Ann Lewis. Principal and Chief Executive Officer, Middlesbrough College. For services to Further Education. Dr. Andrew John Mackintosh. Adviser, The Knowledge Assets Initiative. For services to Science and Technology, and to Enterprise Development. Barbara Hilary Manning. Lately Head of Payments, Banking and Shared Services, Department for Work and Pensions. For services to the Public and to the State Funeral of Her Majesty Queen Elizabeth II. Anthony McGee. Director, Ukraine Task Force, Ministry of Defence. For Public Service. Michael Messinger, LVO, QPM. Lately Chancellor, Order of St. John (England) and Deputy Chairman, St John Ambulance. For voluntary service to St John Ambulance. Colin Morrison, OBE. Founder and Chair, Boarding School Partnerships. For services to Education. Katherine Louise Mosse, OBE. Author. For services to Literature, to Women and to Charity. Ciaran Michael Murphy, KC. Senior Counsel. For services to Criminal Justice. Stuart Neil Luke Murphy. Chief Executive, English National Opera. For services to Opera. Professor Joseph Gerard Nellis. Professor of Global Economy, School of Management Cranfield University. For services to Higher Education, to Economics, to Business and to Charity. Dr. Vanessa Jane Ogden. Chief Executive Officer, Mulberry Schools Trust. For services to Education. René Olivieri. For services to the Charitable Sector. Lynn Margaret Pamment.
Sources: en.wikipedia.org
=== Andrology and embryology laboratories and reproductive tissue banks === CLIA applies to sperm analysis and the postcoital test, but does not apply to andrology or embryology laboratories, to testing performed as part of an assisted reproductive technology (ART), or to reproductive tissue banks. There are no federal personnel requirements. The lack of CLIA applicability has been criticized noting how semen analysis is categorized as a high complexity test whereas the analysis of oocytes and embryos is unregulated, despite similar equipment and techniques in use. There are accreditation programs such as the CAP/ASRM Reproductive Laboratory Accreditation Program (RLAP), and TJC and CAP offer specialty accreditations, but these are voluntary in nature. In the summer of 1991, HHS notified the American Society of Reproductive Medicine (ASRM) and the Society for Assisted Reproductive Technology (SART) that in vitro fertilisation (IVF) and gamete intrafallopian transfer (GIFT) laboratories were to be covered under CLIA '88. However, when CLIA '88 was published on February 28, 1992, it did not explicitly mention andrology and embryology laboratories creating uncertainty in regulatory oversight. In 1992, Senator Ron Wyden (D-OR) introduced the Fertility Clinic Success Rate and Certification Act (FCRCA), colloquially called the "Wyden bill", requiring the Disease Control and Prevention (CDC) to develop a model program for the certification of embryo laboratories, to be carried out voluntarily by interested states. This created initial confusion as to whether CLIA was applicable.
Svetlana Mojsov is a Yugoslav-born Macedonian American chemist who is a Lulu Chow Wang and Robin Chemers Neustein Research Professor at the Rockefeller University. Her research considers peptide synthesis. She discovered the glucagon-like peptide-1 (GLP-1) and uncovered its role in glucose metabolism and the secretion of insulin. Her breakthroughs were transformed by Novo Nordisk into therapeutic agents against diabetes and obesity.
Legend: 0 – no inhibition + – mild/weak inhibition ++ – moderate inhibition +++ – strong/potent inhibition The CYP2D6 enzyme is entirely responsible for the metabolism of hydrocodone, codeine and dihydrocodeine to their active metabolites (hydromorphone, morphine, and dihydromorphine, respectively), which in turn undergo phase 2 glucuronidation. These opioids (and to a lesser extent oxycodone, tramadol, and methadone) have interaction potential with selective serotonin reuptake inhibitors. The concomitant use of some SSRIs (paroxetine and fluoxetine) with codeine may decrease the plasma concentration of active metabolite morphine, which may result in reduced analgesic efficacy. Another important interaction of certain SSRIs involves paroxetine, a potent inhibitor of CYP2D6, and tamoxifen, an agent commonly used in the treatment and prevention of breast cancer. Tamoxifen is a prodrug that is metabolised by the hepatic cytochrome P450 enzyme system, especially CYP2D6, to its active metabolites. Concomitant use of paroxetine and tamoxifen in women with breast cancer is associated with a higher risk of death, as much as a 91 percent increase in women who used it the longest.
== Host/implant interactions == Wound healing of the skin and tendons is a complex coordinated process in the body that happens slowly over weeks or even years. A number of products in the market today aim to affect this process positively, although little data is available on their success. The majority of products are still in the development phases where the (often inflammatory) interactions between the host and the implanted devices are being assessed. Implanted ECM biomaterials fall into two general categories based on how they interact with the host. Incorporating devices eventually allow the growth of cells and passage of blood vessels through the matrix, whereas nonincorporating biomaterials are encapsulated by a wall of fused macrophages. In nonincorporating biomaterials such as Permacol, an acellular porcine dermal implant for hernia repair, it is important that the material is not degraded or infiltrated by the immune system. Encapsulated biomaterials that are recognized as foreign can be degraded and/or rejected by the body and migrate to the outside of the body. In incorporated ECM biomaterials, infiltration by the immune system can occur in as few as seven days, leading to rapid degradation of the device volume. In the case of Graftjacket, an allograft from human dermis, the matrix is quickly populated by host cells as vasculature. The device itself decreased more than 60% in volume, and is replaced with host fibroblasts and macrophages.
These illicit pills often contain "a mix of amphetamines, caffeine and various fillers", which are sometimes referred to as "captagon" (with a lowercase "c"). According to some leaks, militant groups export the drug in exchange for weapons and cash. According to Abdelelah Mohammed Al-Sharif, secretary general of the National Committee for Narcotics Control and assistant director of Anti-Drug and Preventative Affairs, forty percent of users between the ages of twelve and twenty-two in Saudi Arabia are addicted to fenethylline. In 2017, fenethylline was the most popular recreational drug in the Arabian Peninsula. In October 2015, a member of the Saudi royal family, Prince Abdel Mohsen Bin Walid Bin Abdulaziz, and four others were detained in Beirut on charges of drug trafficking after airport security discovered two tons of fenethylline pills and some cocaine on a private jet scheduled to depart for Riyadh, the capital of Saudi Arabia. The following month, Agence France-Presse reported that Turkish authorities had seized two tonnes of fenethylline—about eleven million pills—during raids in the Hatay region on the Syrian border. The pills had been produced in Syria and were being shipped to countries in the Arab states of the Persian Gulf. In December 2015, the Lebanese Army announced that it had discovered two large-scale drug production workshops in the north of the country and seized large quantities of fenethylline pills. Two days earlier, three tons of fenethylline and hashish were seized at Beirut Airport, concealed in school desks being exported to Egypt.
Sources: en.wikipedia.org
Yes, the terms are generally interchangeable. Lyophilization is more common in pharmaceutical and laboratory contexts, while freeze-drying appears widely in food science and general writing. Both describe removal of solvent by sublimation under vacuum after freezing.
Reduced pressure keeps the process below the triple point of water, so ice can sublimate directly to vapor. It also lowers the temperature needed for drying, which helps preserve heat-sensitive materials. Without vacuum, melting or boiling could occur instead of controlled sublimation.
The rate depends on heat transfer to the product and mass transfer of vapor through the dried layer. A cold condenser, adequate vacuum, and suitable shelf temperature all influence speed. Formulation properties such as solid content and collapse temperature also set practical limits.
Residual moisture can influence chemical degradation, cake collapse, and long-term stability. Low moisture levels usually improve stability, but each product has an optimal range.