If you have been reading about sublimation and want a single page that covers the useful parts, this is it: definitions, context, how it is studied, and the questions that come up repeatedly.
Last reviewed on 2025-12-24. Where a claim depends on a specific study, the study is described rather than over-claimed.
Lyophilization removes water from a frozen material by sublimation under reduced pressure. The process begins with freezing, which converts liquid water into ice and fixes the structure of the sample. After freezing, primary drying lowers pressure so ice changes directly to vapor without passing through a liquid phase. Secondary drying then removes bound water that remains after ice sublimation. The result is a dry, porous solid that often retains its original shape.
The low pressure used during drying allows water vapor to move from the ice surface to a cold condenser. Energy supplied as heat drives sublimation but must stay below the collapse temperature of the frozen matrix. If the product becomes too warm, the frozen structure may soften or melt, reducing pore formation and slowing drying. Formulations often include bulking agents, stabilizers, or buffers to support a rigid cake. The final moisture content depends on formulation, freezing rate, and the length of secondary drying.
Freeze-drying is distinct from simple evaporation and from spray drying. Evaporation removes water at temperatures above freezing, while spray drying rapidly dries droplets in a heated gas stream. Lyophilization avoids high temperatures, which can be useful for heat-sensitive materials such as proteins, vaccines, and some foods. The porous cake produced by sublimation dissolves or rehydrates more quickly than a dense dried mass. Not all materials tolerate freezing or the pH shifts that can occur as solutes concentrate during ice formation.
Quality control for freeze-dried forms includes visual inspection, water content measurement, and reconstitution time. A satisfactory cake is typically uniform, porous, and intact, although minor shrinkage or cracking may be acceptable if specifications allow. Karl Fischer titration, thermal gravimetric analysis, and near-infrared spectroscopy are used to measure water content. Reconstitution is assessed by adding a specified diluent and recording the time and ease of dissolution. Microbiological and particulate tests are added when the product is sterile or intended for injection.
Stability of a lyophilized solid depends on water content, temperature, and the physical state of the formulation. Amorphous products may slowly absorb moisture and drop below their glass transition temperature, causing collapse or crystallization. Some proteins and peptides can aggregate even in a dry state, especially when exposed to heat or moisture. Accelerated stability studies at elevated temperature and humidity help estimate shelf life, but real-time data remain the basis for expiration dating.
After drying, a lyophilized product is usually sealed under vacuum or an inert gas to limit moisture and oxygen exposure. The container closure system matters because stoppers and seals can allow moisture ingress over time. Storage conditions are selected from stability studies that track potency, cake appearance, and reconstitution behavior. Many freeze-dried materials are kept at controlled room temperature, while some require refrigeration or protection from light.
| Property | Value | Notes |
|---|---|---|
| Primary phase change | Sublimation | Ice changes directly to vapor under reduced pressure |
| Typical chamber pressure | 0.01–0.5 mbar (1–50 Pa) | Below the triple point of water; product-specific |
| Typical product temperature during primary drying | −40 °C to −10 °C | Kept below collapse temperature |
| Typical residual moisture | 0.5–3% w/w | Target range varies by formulation and use |
| Common synonyms | Freeze-drying; lyophilisation | Lyophilization is the US spelling |
A freeze-dryer consists of a vacuum chamber, temperature-controlled shelves, a condenser, and a vacuum pump. Vials, ampoules, or bulk trays hold the product during the cycle. The condenser traps water vapor as ice at a temperature lower than the product. Cycle development balances shelf temperature, chamber pressure, and time. Scale-up can be difficult because heat and mass transfer change with equipment size, so process analytical tools and conservative validation are often used.
Lyophilization is a dehydration technique in which a product is frozen and the solvent is removed under reduced pressure. The low pressure allows ice to sublimate directly into vapor without passing through a bulk liquid phase. This differs from conventional drying, where heat drives evaporation and can damage heat-sensitive structures. The process is used for biological materials, pharmaceutical formulations, and some foods. Its main advantage is preservation of porous structure and rapid reconstitution.
Freezing is the first stage and sets the ice structure that later becomes the pore network. The formulation is cooled below its freezing point, often with a controlled ramp, and solutes concentrate as ice forms. Primary drying then lowers chamber pressure and supplies heat to sublime the ice. The product temperature must stay below its collapse or eutectic temperature to prevent structural loss. Secondary drying raises the temperature modestly to remove bound water and achieve a low residual moisture.
Analytical methods for lyophilized materials include X-ray diffraction for crystallinity, differential scanning calorimetry for thermal transitions, and scanning electron microscopy for pore morphology. Moisture sorption analysis shows how the cake responds to humidity. These methods help distinguish amorphous from crystalline states and detect phase changes. Open questions remain about how pore structure changes during long-term storage and how best to predict collapse under varied conditions. Comparisons across studies are complicated by differences in formulation, cycle, and storage history.
Quality control for lyophilized products focuses on appearance, moisture level, reconstitution time, and structural integrity. A cake should be uniform, intact, and free of meltback or collapse. Moisture level is measured by Karl Fischer titration or thermogravimetric analysis. Reconstitution time reflects pore structure and formulation. Visual inspection and vial integrity checks detect cracks, stopper defects, or particulate matter. These checks are often performed on samples from each batch. They help confirm that the drying cycle performed as intended.
{\displaystyle Q=\left[m_{\text{N}}\left({\ce {^{\mathit {A}}_{\mathit {Z}}X}}\right)+m_{\text{e}}-m_{\text{N}}\left({\ce {^{\mathit {A}}_{{\mathit {Z}}-1}X'}}\right)-m_{\nu _{\text{e}}}\right]c^{2},}
On June 15, 2017, Finnish restaurant company Restel announced that it is bringing Taco Bell to Finland. The first restaurant opened in central Helsinki on November 9, 2017. Restaurants in Sello and Iso Omena malls in Espoo opened later in November 2017. Finland is the first country to include pulled oats (a meat substitute) in the menu. In 2019, the Taco bell expanded outside the Helsinki metropolitan area to Lappeenranta and Turku. In July 2021, a new branch was opened in Oulu. As of November 2022 there are 16 Taco Bell restaurants in Finland, most of them in the Helsinki metropolitan area.
== Exports == Bangladesh exports processed foods to markets in Asia, the Middle East, Europe and North America. In fiscal year 2023–24, the country exported US$341.73 million worth of agro-processed foods to 100 countries, down from US$383.26 million to 103 countries in the previous fiscal year, according to figures reported by The Daily Star. The Bangladesh Agro-Processors' Association said that 75 percent of processed-food exports during the preceding five fiscal years were concentrated in 13 countries. In 2023–24, the largest reported markets included the United Arab Emirates, Saudi Arabia, the United Kingdom, the United States and Malaysia. Using a different trade classification, the USDA estimated Bangladesh's consumer-oriented food exports at about US$0.4 billion in calendar year 2025. These figures are narrower than statistics for all agricultural exports. The Export Promotion Bureau reported total agricultural-product exports of US$989 million in fiscal year 2024–25.
Caddisfly silk is silk that is secreted by the silk glands of the caddisfly (Trichoptera), similar to Lepidoptera silkworms (B. mori). The larvae use silk to hunt and defend themselves. The silk's underwater binding properties are a subject of ongoing scientific research. Trichoptera, or caddisfly, larvae use silk to hunt and protect themselves in their aquatic environment. Much like silkworms and other Lepidoptera, this silk protein is excreted by specialized silk glands. The silk’s structure is mostly conserved among many different caddisfly species, and can be used to bind debris including rocks, sticks, twigs and shells, as well as to build nets for catching prey. Caddisflies, which spend the majority of their life cycle in the larval stage, need these casings to protect their underbellies and pupate. Caddisfly silk is very strong and durable. Because their silk must be able to bind to a variety of components while completely submerged in water, it is therefore being studied for potential applications as a waterproof adhesive.
Sources: en.wikipedia.org
The iodine pit, also called the iodine hole or xenon pit, is a temporary disabling of a nuclear reactor due to the buildup of short-lived neutron poisons in the reactor core. The main isotope responsible is 135Xe, mainly produced by beta decay of 135I. 135I is a weak neutron absorber, while 135Xe is the strongest known neutron absorber. When 135Xe builds up in the fuel rods of a reactor, it significantly lowers their reactivity, by absorbing a significant amount of the neutrons that provide the nuclear reaction. The presence of 135I and 135Xe in the reactor is one of the main reasons for its power fluctuations in reaction to change of control rod positions. The buildup of short-lived fission products acting as nuclear poisons is called reactor poisoning, or xenon poisoning. The buildup of stable or long-lived neutron poisons is called reactor slagging.
=== Lixisenatide in neurodegenerative diseases === Results from a research work which was done by McClean PL et al. demonstrated that the GLP-1 receptor agonists liraglutide and lixisenatide which are on the market as treatments for type 2 diabetes show promise as potential drug treatments of Alzheimer disease AD. Lixisenatide was equally effective at a lower dose compared to liraglutide in some of the measured parameters after ten weeks of daily intraperitoneal injections with liraglutide (2.5 or 25 nmol/kg) or lixisenatide (1 or 10 nmol/kg) or saline of APP/PS1 mice at an age when amyloid plaques had already formed. When analyzing synaptic plasticity in the hippocampus, LTP was strongly increased in APP/PS1 mice by either drug, with more effectiveness accomplished with lixisenatide. The reduction of synapse numbers seen in APP/PS1 mice was prevented by the two drugs. The amyloid plaque load and dense-core Congo red positive plaque load in the cortex were reduced by both drugs at all doses. The chronic inflammation response (microglial activation) was also reduced by all treatments. Cai HY et al. demonstrated in a study that lixisenatide could reduce amyloid plaques, neurofibrillary tangles and neuroinflammation in the hippocampi of 12-month-old APP/PS1/tau female mice; activation of PKA-CREB signaling pathway and inhibition of p38-MAPK might be the important mechanisms in the neuroprotective function of lixisenatide. So, lixisenatide might have the potential to be developed as a novel therapy for AD.
Reuptake inhibitors (RIs) are a type of reuptake modulators. It is a drug that inhibits the plasmalemmal transporter-mediated reuptake of a neurotransmitter from the synapse into the pre-synaptic neuron. This leads to an increase in extracellular concentrations of the neurotransmitter and an increase in neurotransmission. Various drugs exert their psychological and physiological effects through reuptake inhibition, including many antidepressants and psychostimulants. Most known reuptake inhibitors affect the monoamine neurotransmitters serotonin, norepinephrine (and epinephrine), and dopamine. However, there are also a number of pharmaceuticals and research chemicals that act as reuptake inhibitors for other neurotransmitters such as glutamate, γ-aminobutyric acid (GABA), glycine, adenosine, choline (the precursor of acetylcholine), and the endocannabinoids, among others.
== Alternatives to EDTA == Interest in environmental safety has raised concerns about biodegradability of aminopolycarboxylates such as EDTA. These concerns incentivize the investigation of alternative aminopolycarboxylates. Candidate chelating agents include nitrilotriacetic acid (NTA), iminodisuccinic acid (IDS), polyaspartic acid, S,S-ethylenediamine-N,N′-disuccinic acid (EDDS), methylglycinediacetic acid (MGDA), and L-Glutamic acid N,N-diacetic acid, tetrasodium salt (GLDA).
=== Breeding === The giant gourami is an egg layer and builds a nest from plant fibers. Both male and female gourami participates at building nests, though the male appears to play a more prominent role. The male and female are distinguished by the dorsal fins and body color. The dorsal fin on the male ends in a point, and the body is darker changing to nearly black during spawning. After building nest the eggs will be laid before next 24 hours. When breeding, the water in the tank should be decreased to about 20 cm (8 in) deep and the temperature should be 28 °C (82 °F). After spawning, the female is removed to a separate tank as the male will jealously guard the eggs, in a captive environment, sometimes becoming aggressive towards the female. The eggs hatch in 24 hours. They must be kept in a dark aquarium.
Sources: en.wikipedia.org
A written description of a trial/study of any therapeutic, prophylactic, or diagnostic agent conducted in human subjects, in which the clinical and statistical description, presentations, and analyses are fully integrated into a single report. (ICH E6) Clinician
===== PI 88788 ===== The vast majority of cultivars in the US have soybean cyst nematode resistance (SCN resistance), but rely on only one breeding line (PI 88788) as their sole source of resistance. (The resistance genes provided by PI 88788, Peking, and PI 90763 were characterized in 1997.) As a result, for example, in 2012 only 18 cultivars out of 807 recommended by the Iowa State University Extension had any ancestry outside of PI 88788. By 2020 the situation was still about the same: Of 849 there were 810 with some ancestry from PI 88788, 35 from Peking, and only 2 from PI 89772. (On the question of exclusively PI 88788 ancestry, that number was not available for 2020.) That was speculated to be in 2012—and was clearly by 2020—producing SCN populations that are virulent on PI 88788.
cathode An electrode from which the conventional electric current (the flow of positive charges) exits a polarized electrical circuit. Positively charged cations always move toward the cathode, though the cathode's polarity can be positive or negative depending on the type of electrical device and how it is being operated. Contrast anode.
=== June === 1 June – A bioRxiv preprint reports the first use of base editing to alter the genome of early human embryos. Researchers at Columbia University used the technique to introduce precise single-letter DNA changes without the large chromosomal alterations previously associated with double-strand-break CRISPR gene editing, while noting that the approach remains far from clinical use and raises ethical questions over human germline engineering. 3 June – A report by the United Nations University Institute for Water, Environment and Health estimates that global data centre electricity consumption could reach 945 TWh by 2030, driven partly by growing demand for artificial intelligence, with associated water use rising to 9.3 trillion litres and carbon dioxide emissions to 399 million tonnes. 4 June – Chinese researchers discover the two-state model of liquid water theorizing that water is composed of two distinct and interconvertible local structures at the high and low density phase boundary. 5 June – Researchers at the University of Cambridge and DIOSynVax report the first human clinical trial of a vaccine whose active component was designed entirely by computer simulations. The candidate pan-Sarbecovirus vaccine, pEVAC-PS, uses a machine-learning-designed "super-antigen"; a phase I trial in 39 healthy volunteers finds it safe and able to trigger immune responses to SARS-CoV-2, SARS-CoV-1, and related bat coronaviruses.
Smartphones, tablets, and wearable computers have allowed people to monitor their health. These devices run numerous applications that are designed to provide simple health services and the monitoring of one's health with finding as critical problems to health as possible. An example of this is Fitbit, a fitness tracker that is worn on the user's wrist. This wearable technology allows people to track their steps, heart rate, floors climbed, miles walked, active minutes, and even sleep patterns. The data collected and analyzed allow users not just to keep track of their health but also help manage it, particularly through its capability to identify health risk factors. There is also the case of the Internet, which serves as a repository of information and expert content that can be used to "self-diagnose" instead of going to their doctor. For instance, one need only enumerate symptoms as search parameters at Google and the search engine could identify the illness from the list of contents uploaded to the World Wide Web, particularly those provided by expert/medical sources. These advances may eventually have some effect on doctor visits from patients and change the role of the health professionals from "gatekeeper to secondary care to facilitator of information interpretation and decision-making." Apart from basic services provided by Google in Search, there are also companies such as WebMD that already offer dedicated symptom-checking apps.
Sources: en.wikipedia.org
Lyophilization relies on sublimation, so water moves from solid ice to vapor without becoming liquid. The material is frozen, pressure is reduced, and controlled heat is supplied. Vapor is captured on a cold condenser, leaving a dry porous solid.
The process has three main stages: freezing, primary drying, and secondary drying. Freezing sets the ice structure, primary drying removes free ice, and secondary drying removes bound water. Each stage uses specific temperature, pressure, and time settings.
No, it is a drying method rather than a sterilization method. Removing water can limit microbial growth, but it does not reliably kill microorganisms. Sterility must come from separate steps such as filtration, heat treatment, or aseptic processing.
Sealed vials or containers should be kept at the temperature specified by stability data, often controlled room temperature or 2–8 °C. Moisture and oxygen barriers are important because both can degrade sensitive materials. Opened containers may need immediate use or protection from ambient humidity.